Hi all, I have a nearly pristine Pismo with 512 Mb of Ram, happily running both Mac OS X 10.3.9 and Mac OS 9.2.2 on a 60 Gb hard drive. It has an Airport card, which I can use jus…

A few points to add to the good advice others have contributed: - As folks have said, Tiger must be installed on the first partition, and the partition should be smaller than 7.45…

I did not look at them that closely but that is a definite possibility. Either way, it was a benefit since the two ram chips originally in the Lombard were not suitable for the un…

Wallstreet and Lombard both have 66MHz system busses and can use PC66 SO-DIMMs. If someone went the cheap route on the Wallstreet and only used bare-minimum spec PC66 SDRAM (yes, …

I reseated the CPU to no go. I took the RAM out and put it into my Lombard along with a new 20GB HD, instant boot. Works great. I installed the old Lombard RAM which apparently …

Do the old "disconnect the PRAM battery", and reseat the CPU card - it goes in with a "thunk" sound. JB

When i put the my duo 2300c into the original duo dock after it has been sitting for a few weeks it boots just fine and runs for about a minute then shuts down. Each time i start i…

I was given a Pismo stock except the HD was smaller. After aquiring a fully loaded Wallstreet 14" with hinges not doing so well. I gutted it intended on making a good pismo out o…

I'm back, but until I re-learn how to embed a URL or get around to copy/pasting my '''fritter return to the web announcement in the lounge, you folks are SOL on the full story.... …

Yay! He's back! Glad to hear from you, Trash! Peace, Drew Click to expand... Thanks for the welcome comrade! In just a few minutes my friend is helping me pick up 9' of 6" b…

Yay! He's back! Glad to hear from you, Trash! Peace, Drew

As a crazy idea yesterday, I also wondered about the feasibility of hooking another wire to the printer port of both GS's. Since the modem port wire is definitely going to have to …

I'm back, but until I re-learn how to embed a URL or get around to copy/pasting my '''fritter return to the web announcement in the lounge, you folks are SOL on the full story. ht…

Cool! I imagine the taking turns issue would depend largely on what sort of game you're planning. Any kind of real time action game is going to be problematic because you're almost…

Yeah, I remembered NadaNet a few hours after I typed the original post. Since then, I got out my 2 IIgs's and my trusty Super Serial Card Installation and Operating Manual, and set…

Michael Mahon did a pong demo over NadaNet recently... just start googling ;-) But I have heard of something similar being done in the '80s, though I'm not sure what interface w…

I'm curious to know if there are any network games for the 8-bit Apple II? Such as where you'd connect two Apples together with a serial cable (or, heaven forbid, cassette ports) t…

What I did when I had this problem is take the hard drive out, put it into a tiger capable mac, then install tiger on that first partition, before the user setup process, just tak…

I did the same install on a beige G3 some back and had a couple of problems. I had to format a partition not at but slightly under 8 gb and it had to be the first partition on the …

I wonder if I should partition the whole 80gb drive into 7.5gb partitions and see what that does. Click to expand... You'd just end up with a whole lot of 7.5GB patitions, whic…

Just tried it. Screwed around with the drive configuration and got the same results as before. I wonder if I should partition the whole 80gb drive into 7.5gb partitions and see wha…

Just tried it. Screwed around with the drive configuration and got the same results as before. I wonder if I should partition the whole 80gb drive into 7.5gb partitions and see wha…

try making is something like 7.5GB. that's probably the problem.

Ok, so if you read my buildup thread, you know that I have a 300 MHZ beige G3 minitower that I'm trying to install tiger on. It has 768 MB ram, rev. c ROM (recognizes second hard d…

Can you approach it from the server side? Can you add VT emulation config files to your home directory and profile?