Thread
DOA G4/DA/466 = ATX shenanigans . . .
I'm gonna cry a lot . . . 
. . . if I can't get my baby up and running again. It has been my workhorse for over twelve years now and was the last half of my original username.
Symptom:
Press Power Button = NADA! xx(
Tried re-seating most of the innards after blowing all foreign objects out of the case with my compressor.
First one was the power button board interconnect.
Next planned step is to pull out all the extra cards and HDDs for installation in the Dual Gig QS'02.
Has anyone tried shorting pins on the Power/Reset Button Board's Cable to test "Power On?"
I'm heartbroken, so I'm probably overlooking some obvious stuff, it's like a doctor working on one of his children . . . a HUGE no, no!
Any suggestions?
. . . if I can't get my baby up and running again. It has been my workhorse for over twelve years now and was the last half of my original username.Symptom:
Press Power Button = NADA! xx(
Tried re-seating most of the innards after blowing all foreign objects out of the case with my compressor.
First one was the power button board interconnect.
Next planned step is to pull out all the extra cards and HDDs for installation in the Dual Gig QS'02.
Has anyone tried shorting pins on the Power/Reset Button Board's Cable to test "Power On?"
I'm heartbroken, so I'm probably overlooking some obvious stuff, it's like a doctor working on one of his children . . . a HUGE no, no!
Any suggestions?
Power supply is dead. The non-working DA 466 I got for free was the same way. No response whatsoever from it. I took apart the supply to find 3 resistors fried...nothing else looked bad. I replaced them and all 3 fried as soon as I plugged the power cord in the wall.
That figures . . . how did you get yours back online? ATX transplant?
Are there any readily available donors?
Are there any readily available donors?
ATX Transplant for sure 
Switch over to an ATX for sure. I haven't done mine yet... it's still sitting in the closet.
Roger that, good buddy! :approve:
The obvious is the PRAM battery although I think you at least get a light when they are dead. I don't know how many of those I "fixed" for people by pulling the battery out.
The actual power button boards go bad too.
That said, in all actuality it probably is the PSU at this age.
The actual power button boards go bad too.
That said, in all actuality it probably is the PSU at this age.
Thanks for the suggestion, mcd.
No joy in mudville. I thought I'd replaced the PRAM bat with one of my lot of new blue ones, but it was purple w/ green on black racing stripes. Swapped it out and blue failed too.
Just out of curiosity, which holes in the Female/PSU side of the Power Board Interconnect Cable do I stick the pins into for wiring up a momentary switch temporarily to the PSU?
I've got a BrandNIBinCellophane 400W ATX PSU on hand, but I'll need to see if I can trade up/sideways. This one was meant for a Pentium System w/LOTS of HDDs/Opticals, etc.
+5V rail is 4A shy of the DA's 20A spec.
+3.3V rail is shy of the DA'd 24A spec.
+12V1 rail is 2x DA's 8.0A spec.
+12V2 rail is 2x DA's 8.0A spec.
-12V rail is .8A vs. .25A for the DA spec.
On the ATX: what the heck is the 2.5A +5Vsb rail, Processor or VidCard Power?
On the DA what the dickens is a 4.04A +28V VS Rail? :?:
Does anyone have a suggestion for a suitable ATX PSU?
No joy in mudville. I thought I'd replaced the PRAM bat with one of my lot of new blue ones, but it was purple w/ green on black racing stripes. Swapped it out and blue failed too.
Just out of curiosity, which holes in the Female/PSU side of the Power Board Interconnect Cable do I stick the pins into for wiring up a momentary switch temporarily to the PSU?
I've got a BrandNIBinCellophane 400W ATX PSU on hand, but I'll need to see if I can trade up/sideways. This one was meant for a Pentium System w/LOTS of HDDs/Opticals, etc.
+5V rail is 4A shy of the DA's 20A spec.
+3.3V rail is shy of the DA'd 24A spec.
+12V1 rail is 2x DA's 8.0A spec.
+12V2 rail is 2x DA's 8.0A spec.
-12V rail is .8A vs. .25A for the DA spec.
On the ATX: what the heck is the 2.5A +5Vsb rail, Processor or VidCard Power?
On the DA what the dickens is a 4.04A +28V VS Rail? :?:
Does anyone have a suggestion for a suitable ATX PSU?
It's probably time to start a Hacks Topic for this . . . maybe I'll just move & re-title it . . . or clone it, it's topical right here. My buddy eeun posted this over on 'fritter:
Power Mac G4 (MDD) ATX Power Supply conversion
When the Power Button test invariably fails, I'm going to start doing a "Newt" graphic along the lines of the CC Frog graphic.
I need to do ATX conversions for:
G4 466 DA
Macintosh IIsi = just about everything from that era
Performa 6360
Radius 81/110 = 6100 etc.
DuoDocks
I might as well get 'em all set up on one big .PDF export from Illustrator.
I'm leaning toward a PCB approach for soldering the lopped off Mac harness to one side with the female end of an ATX conversion cable on the other side. If I do it that way it's a cinch to swap out another ATX PSU if the first one dies. I could hook up curbed ATX PSUs after testing or to test out physical mods of odd form factored ATX PSU guts adapted to fit into Mac PSU boxen. The PCB would be universal, small and flat, fitting into just about any case. It will have holes for standoffs so it can be mounted inside or outside just about any Mac PSU's sheet metal.
Comments/suggestions? What do you think, ojfd? :?:
Power Mac G4 (MDD) ATX Power Supply conversion
When the Power Button test invariably fails, I'm going to start doing a "Newt" graphic along the lines of the CC Frog graphic.
I need to do ATX conversions for:
G4 466 DA
Macintosh IIsi = just about everything from that era
Performa 6360
Radius 81/110 = 6100 etc.
DuoDocks
I might as well get 'em all set up on one big .PDF export from Illustrator.
I'm leaning toward a PCB approach for soldering the lopped off Mac harness to one side with the female end of an ATX conversion cable on the other side. If I do it that way it's a cinch to swap out another ATX PSU if the first one dies. I could hook up curbed ATX PSUs after testing or to test out physical mods of odd form factored ATX PSU guts adapted to fit into Mac PSU boxen. The PCB would be universal, small and flat, fitting into just about any case. It will have holes for standoffs so it can be mounted inside or outside just about any Mac PSU's sheet metal.
Comments/suggestions? What do you think, ojfd? :?:
Those are standby rails. You can connect the 5v of ATX to the 28V of the Mac and be able to boot(but you are not going to be using Firewire or ADC displays) but I have noticed that if you keep it that way for a long time it eventually starts having trouble cold booting. For my DA at the moment I found a 24V 4A dell notebook power adapter and wired it into my ATX extension. It has been working well but I do not have any ADC displays or bus powered FireWire devices to test it with. All I know is that it is not developing an issue overloading on cold boot like the couple other PSUs I had been swapping in and out during it's life and during hardware changes.And it is not just about quality either. One was a 650W modular Antec unit, that 650 is mostly made up by the 12V rails and the standby was seemingly not good enough for my DA I guess. :/ (this PSU went on to power a PC with crazy overclock and other fun goodies without any issue.)
The DA currently has a 350W Seasonic + the dell notebook adapter and is doing well.
Seasonic & Corsair are loved brands. As is Antec.
Excellent tips, thanks, MacJunky!
I think maybe I'll put a spot on the PCB for that 4A battery/power adappter of yours, how much do they cost?
Perhaps we can coax ojfd or tomlee59 to come up with a simple circuit for the adapter PCB that'll squeeze 24V out of the two +12V rails on the ATX PSUs? That'd be a better approach . . . two batteries in series work . . . maybe with a trio of fuses, some diodes, resistors, caps and other black magic it'll work . . .
. . . or not! :
This is definitely turning into yet another Hacks & Development project. :approve:
I think maybe I'll put a spot on the PCB for that 4A battery/power adappter of yours, how much do they cost?
Perhaps we can coax ojfd or tomlee59 to come up with a simple circuit for the adapter PCB that'll squeeze 24V out of the two +12V rails on the ATX PSUs? That'd be a better approach . . . two batteries in series work . . . maybe with a trio of fuses, some diodes, resistors, caps and other black magic it'll work . . .
. . . or not! :
This is definitely turning into yet another Hacks & Development project. :approve:
Content Collection:
ATX <-> Quicksilver Pinouts
DA, QS & MDD <-> ATX Pinouts
Pinout links for all other Mac Connectors would be greatly appreciated.
Thanks, eeun!
. . . and now for a PCB Layout!
)
edit: PMs sent to both EEs! Now it's off to upgrade the current ATX PSU . . .
ATX <-> Quicksilver Pinouts
DA, QS & MDD <-> ATX Pinouts
Pinout links for all other Mac Connectors would be greatly appreciated.
Thanks, eeun!
. . . and now for a PCB Layout!
) edit: PMs sent to both EEs! Now it's off to upgrade the current ATX PSU . . .
Oh shoot, I am sorry, it is 20v.. Still good though.
Anyway.
I picked up my adapter at a local shop for nothing so I do not know what they normally cost.
Also, this has the front panel header pinout:
http://www.outofspec.com/frankenmac/wire.shtml
Anyway.
I picked up my adapter at a local shop for nothing so I do not know what they normally cost.
Also, this has the front panel header pinout:
http://www.outofspec.com/frankenmac/wire.shtml
Wow, that was fast! I got the answer I sort of expected from tomlee59.
Due to the two 12V rails sharing a common ground and coming in parallel off the same PSU, you cannot wire them in series . . . NUTS . . . }
Wall wart is looking the easiest to implement, but our EE tomlee59 said:
Any help on that end of things would be much appreciated! :approve:
Anybody got the IIsi/IIci/Q700 etc. cable/connector pinout handy?
IIsi/IIci/Q700 Pinouts
] ]'>
Due to the two 12V rails sharing a common ground and coming in parallel off the same PSU, you cannot wire them in series . . . NUTS . . . }
Wall wart is looking the easiest to implement, but our EE tomlee59 said:
I'll have to look into that one, but electron pushing isn't my strong point . . . it's a very weak point, at that. :I
Any help on that end of things would be much appreciated! :approve:
Anybody got the IIsi/IIci/Q700 etc. cable/connector pinout handy?
IIsi/IIci/Q700 Pinouts
My Pile-o-DuoDongles are 24V! [
] ]'>
You'll find my experience of the DA-ATX mod here.
Of note:
Use an ATX power extension cable for the mod.
Of note:
NB: of course, this will not run an ADC monitor, or any bus-powered FW peripherals, but it will boot.
Use an ATX power extension cable for the mod.
Yeah, I realized my converter cable was B@$$@CKWARD$ for the task.
Since I'm doing a PCB Adapter (I LOATHE wire splicing) to simplify the hookups, I'll be looking into tomlee59's suggestion for adding a "boost converter" to the board. That way I'll get a true 28V line and I'll just leave the components for that section unpopulated for the IIsi/Q700 conversions.
Since I'm doing a PCB Adapter (I LOATHE wire splicing) to simplify the hookups, I'll be looking into tomlee59's suggestion for adding a "boost converter" to the board. That way I'll get a true 28V line and I'll just leave the components for that section unpopulated for the IIsi/Q700 conversions.
I just realized that the "power boost" section of the PCB will be necessary for the 18V(?) Motor in the DuoDock.
Not to be buzz-kill-y or anything, but as cool as some sort of universal ATX-to-Apple-whatever PCB board might sound might it not be worth the trouble to just crimp together a temporary adapter and make *sure* that the problem with the G4 is the power supply? Or did that already happen and I missed it in the back-and-forth?
You don't have to actually mod the ATX supply. They sell extension cables cheaply enough. (That's what I hacked up when I did an ATX->iMac conversion.)
With regards to using a boost converter to supply your 28v, I'm somewhat skeptical that's a good idea if you intend to actually power an ADC monitor, particularly a CRT one. I don't know how many watts an ADC monitor typically pulls but I suspect it's enough that a few little components stuck on your adapter cable might be hard-pressed to handle it without some serious thought given to heat dissipation. (Judging from the commercial units for car applications/etc it's easy to find pictures of a 5 amp output 12-24v unit typically comes encased in a 3 inch square heat sink...)
You don't have to actually mod the ATX supply. They sell extension cables cheaply enough. (That's what I hacked up when I did an ATX->iMac conversion.)
With regards to using a boost converter to supply your 28v, I'm somewhat skeptical that's a good idea if you intend to actually power an ADC monitor, particularly a CRT one. I don't know how many watts an ADC monitor typically pulls but I suspect it's enough that a few little components stuck on your adapter cable might be hard-pressed to handle it without some serious thought given to heat dissipation. (Judging from the commercial units for car applications/etc it's easy to find pictures of a 5 amp output 12-24v unit typically comes encased in a 3 inch square heat sink...)
Like I said, I've got several permutations to fab. My ADC monitors are a miniscule 17" CRT & LCD pair and I won't be running them off the DA, but the FireWire implications are important for my USB 1 ONLY OS of choice! A Duo AC Adapter Lug would make a good addition to the circuit if tomlee59's suggested parts don't pan out for FireWire.
I will be needing the 18V(?) DuoDock rail though, but that's a fairly low draw motor geared WaaayTFHeck down. }
I will be needing the 18V(?) DuoDock rail though, but that's a fairly low draw motor geared WaaayTFHeck down. }
I'm curious, what do you have use that's FireWire and bus powered?
Wayne
Wayne
One can always use an external powered Firewire hub.
I second Gorgonops' suggestion: do the simplest possible mod to get the DA booting, and thus determine that it is in fact the PS at fault, then move on to a multi-purpose ATX-to-Mac board design.
IIRC, there wasn't a whole lot of wire splicing involved - maybe one or two lines. Most of it was simply moving pins around in the motherboard-end pin shroud of the extension cable.
I second Gorgonops' suggestion: do the simplest possible mod to get the DA booting, and thus determine that it is in fact the PS at fault, then move on to a multi-purpose ATX-to-Mac board design.
IIRC, there wasn't a whole lot of wire splicing involved - maybe one or two lines. Most of it was simply moving pins around in the motherboard-end pin shroud of the extension cable.
First I need to eliminate the Power Button Board before I mangle the original PSU via cable-ectomy.
This is my baby, so I'd rather hazard a few lesser ATX Boxen/MoBos for practice.
My beautiful Graphite (favorite MacColor treatment) G4/466 DA has already lain comatose for a month, another won't matter . . .
I haven't sourced the extension cables yet, they'll be back in stock in a week.
I've got (I think) an acceptable CrapShack prototyping board in stock.
I traded the Pentium Board PSU up to a better suited Cooler Master 500W PSU, but it's 2A shy of the DA's 24A spec on the 3.3V rail . . . probably doesn't matter?
It only set me back an additional $13, but I'm going to compare it to the next $30-$40 bump units available before starting, but they require adding power lines as needed, which may be a plus?
I've got smaller units on hand for the MacintoshClassicIIIColorTVp™ and SuperIIsi™ hacks.
I think I'll prototype the PCB first . . .
. . . or not! :-/
edit: I just went to remove the PSU for a trial fitting of the ATX unit and the DA's troubleshooting Power Strip had been left on. This puppy is still cozy warm . . . 8-o
. . . indicating standby power!?! :?:
This is my baby, so I'd rather hazard a few lesser ATX Boxen/MoBos for practice.
My beautiful Graphite (favorite MacColor treatment) G4/466 DA has already lain comatose for a month, another won't matter . . .
I haven't sourced the extension cables yet, they'll be back in stock in a week.
I've got (I think) an acceptable CrapShack prototyping board in stock.
I traded the Pentium Board PSU up to a better suited Cooler Master 500W PSU, but it's 2A shy of the DA's 24A spec on the 3.3V rail . . . probably doesn't matter?
It only set me back an additional $13, but I'm going to compare it to the next $30-$40 bump units available before starting, but they require adding power lines as needed, which may be a plus?
I've got smaller units on hand for the MacintoshClassicIIIColorTVp™ and SuperIIsi™ hacks.
I think I'll prototype the PCB first . . .
. . . or not! :-/
edit: I just went to remove the PSU for a trial fitting of the ATX unit and the DA's troubleshooting Power Strip had been left on. This puppy is still cozy warm . . . 8-o
. . . indicating standby power!?! :?:
The outofspec page has the front panel header pinout, just momentarily connect pins 3 and 6 shown on the page.
You might also try an orig Apple USB Keyboard with the power button. I *think* those work with the DAG4, I recall hearing that apple canned the ability for certain newer ones to use the keyboard power button but I do not remember what models that might have been or if it was true or not. *shrug*
Yep. I saw that pinout in the link, thanks, but I think I'll probably try the power button on one of my two ADC Monitors . . . I just discovered them yesterday!
Then again, I've got jumper wires and an ATX harness with the momentary switch handy!
Decisions, decisions!)
edit: I gave it a REALLY low rent ghetto try over lunch, I'll do it better to confirm after work, but so far there's no joy on the Power Button Board fix front.
Then again, I've got jumper wires and an ATX harness with the momentary switch handy!
Decisions, decisions!
) edit: I gave it a REALLY low rent ghetto try over lunch, I'll do it better to confirm after work, but so far there's no joy on the Power Button Board fix front.
Still no joy, but four extension cables are sitting here along with the DA's ATX PSU and a long skinny one for the SuperIIsi™ Hack..
I came up with another couple of notions for new additions to the Universal ATX Conversion PCB.
At the very least, I'll put pads for assorted female power jacks so a Lump on a Rope can be easily tacked on for the ADC standby Power Rail. The circuit for using an aux lump to jump the 12V Rail of the ATX up to the proper spec to run a Display ought to be a lot easier than doing thw entire conversion on the board . . . or not.
Either way, it needs to be done! :approve:
Meanwhile, here's a link to a couple more Rainbow Mac circuits to add to the Universal Adapter PCB. 68k Soft/Hard 68k Power and ATX conversions . . .
I came up with another couple of notions for new additions to the Universal ATX Conversion PCB.
At the very least, I'll put pads for assorted female power jacks so a Lump on a Rope can be easily tacked on for the ADC standby Power Rail. The circuit for using an aux lump to jump the 12V Rail of the ATX up to the proper spec to run a Display ought to be a lot easier than doing thw entire conversion on the board . . . or not.
Either way, it needs to be done! :approve:
Meanwhile, here's a link to a couple more Rainbow Mac circuits to add to the Universal Adapter PCB. 68k Soft/Hard 68k Power and ATX conversions . . .
Resistors burning up the the PSU might be signs that one or more of the switching FETs have shorted out and it's forcing current down the line, destroying what is the point of highest resistance (in this case, not the traces).
ATX PSU conversions suck to do. First at least check to see if any of your FETs have shorted before you fully call the original PSU a write-off.
ATX PSU conversions suck to do. First at least check to see if any of your FETs have shorted before you fully call the original PSU a write-off.
I'll definitely check that out too, when the time comes.
It's back burnered for the DA Resurrection for the nonce. I moved the lowly ATI Card to the QS'02 because it runs my 1080p Monitor just fine. I yanked out the ATA Card to install in my Dual Core ATOM board's PCI Slot to finalloy get it up and running (since my girlfriend gave it to me last June : ) because I haven't got any SATA Drives yet, but soon!
I'll be setting up the QS'02 before taking up the Resurrection Project.
I might just get a better DA to upgrade my baby and have some spare parts around. [
] ]'>
It's back burnered for the DA Resurrection for the nonce. I moved the lowly ATI Card to the QS'02 because it runs my 1080p Monitor just fine. I yanked out the ATA Card to install in my Dual Core ATOM board's PCI Slot to finalloy get it up and running (since my girlfriend gave it to me last June :
) because I haven't got any SATA Drives yet, but soon!I'll be setting up the QS'02 before taking up the Resurrection Project.
I might just get a better DA to upgrade my baby and have some spare parts around. [
] ]'>
Well, this is just a dumb thought, but if you needed 24V to power the monitor that an ATX power supply wont do, Another engineering hack approach is to find a dual-rail 12V power supply, some gamer power supplies have 2 separate 12V rails/windings in the ATX power supply. Find the rail opposite of the one that is used for regulation, remove the original rectifier, and form a diode/capacitor voltage doubler rectifier circuit off that particular winding.
Another/easier approach would be to experiement with some magnet wire on a cheap power supply, and wrap the transformer with another layer of magnet wire to derive a new winding for your 18v/24v/28v setup. This would work as well.
You could use a TO-220 based 7818 regulator as well for the 24v or 28v to 18V, but only at 1 amp or so.
Another/easier approach would be to experiement with some magnet wire on a cheap power supply, and wrap the transformer with another layer of magnet wire to derive a new winding for your 18v/24v/28v setup. This would work as well.
You could use a TO-220 based 7818 regulator as well for the 24v or 28v to 18V, but only at 1 amp or so.
Sounds like it would be a LOT less expensive to buy two smaller, NON-GAMER ATX PSUs and easier to build a black box to output the higher voltages.
Me no keen on magic smoke emanations or flames escaping . . . 8-o
Me no keen on magic smoke emanations or flames escaping . . . 8-o
I just like to get my hands dirty 
Black Box Approach: Linear Technologies has a good set of DC-DC buck/boost converter ICs and design guides. Some of them even have development boards with all the components already in place.
Here is a datasheet to an IC from National SemI:
http://www.ti.com/lit/ds/symlink/lm2586.pdf
The circuit you will be interested in, is page 24 of the PDF.
Black Box Approach: Linear Technologies has a good set of DC-DC buck/boost converter ICs and design guides. Some of them even have development boards with all the components already in place.
Here is a datasheet to an IC from National SemI:
http://www.ti.com/lit/ds/symlink/lm2586.pdf
The circuit you will be interested in, is page 24 of the PDF.